Got some stuff done on the front beam/axle on the Highroof bus this week. Fitted new grease zerks to the beam, installed a new center swivelpin and bushings, test fitted the new brakebooster, 4 new needlebearings (made a tool so they were easy to pull out). They were seated 8mm inside the tubes. Used a old bearing to knock them in again, and then the tool the last bit. New dustcovers mounted too. Got the axle bolted up in the frame on the bus and during the weekend, I will start installing torsionarms, spindles, tierods etc. The bus starts to look really nice, atleast underneath! 😉 More pics coming soon!

bild136

bild137

bild138

bild139

bild140

bild141

 Volkswagens original tool

 

bild142

bild143

bild144

bild145

bild146

bild147

bild148

Have sandblasted alot of parts in the new cabinet, so nice to have. No need for waiting on the mediablasting company any more. Just put it in the box and go! Got a box full of new parts from Justkampers.com yesterday too. Brakeservo, starter, all brakepipes, front beam seals, 4 torsionarms with new pressed in balljoints, transmission gaskets and seals etc. Also scored a NOS Eberspächer combustion/airpump for the BA6 heater. Found a supplier in the UK of new BERU glowplugs for BA6, the GZE201 plug replaces the old (original) BZE22. Have anyone tried the new GZE201? Let me know how it worked: info@maindrive.org

Have scraped and cleaned all of the chassi during the last 2 weeks. Hope to push on further with the chassi this week and weekend and get it primered, seam sealed, undercoated and painted in body color. After that the chassi is ready to get all the new parts bolted on! More coming soon…

bild89
bild89b bild90 bild91 bild92 bild93 bild93b bild94 bild95 bild96 bild97 bild98 bild99 bild100 bild101 bild102 bild103

Doing some really boring work on the Highroof Baywindow at the moment. Specially when it’s -20 celsius outside. Removing all of the old undercoating. Work that takes alot of blood, sweat and tears and is not showing much later, but good to know it’s like new under also. Only going to drive it on the summers anyway. Next time I can start sanding the chassi and lay a coat of rust protection (epoxy primer). Then add a new layer of fresh undercoating, that sort thats possible to paint over. So when it have dried for some days I can paint all of the underside in top color, VW L20 Marino yellow. Ready for all the new parts, wires, hoses, grommets, bearings, bushings, balljoints, steering rods, brakelines, servobooster basicly every nut and bolt!

When the chassi is painted and ready I can start restoring the frontbeam, transmission and get the Eberspächer BA6 working again. A really good and clever heater, much better then the older BN4 ones. Will be nice on chilly mornings in the spring!

Still looking for some parts if someone have for sale? NOS parts for BA6 is intresting, like sparkplugs (BZE22) etc. Also looking for a pair of the slider rail metal covers (held with 2 screws). Engine cooling thin and heatexchangers is missing. Send me a mail on: info@maindrive.org

bild73

bild74
Chassi parts that are going to be sandblasted and painted/restored.

bild75

 

 

 

 

 

 

 

 

 

 

 

No more undercoating. Just some wires and tubes that needed to be removed before sanding and primer. Here you can see factory grey primer and the orange overspray from body. When I am done with this chassi it will be better and nicer than it was from factory for sure.

bild78

bild76
Color on chassi will be the same as on the body, original VW color, L20A Marino yellow. Period correct.

bild77

bild80
Can’t wait to start bolting on new parts on the painted chassi!

bild79

bild81

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Replacing all rust with new metal on Benny’s bus, the VW transporter from 1983. Hope to finish the rest tonight and then it’s ready for sanding/bodywork/paint. New rubberseals for the all 6 windows, new bushings for frontend and new mirrors from Just Kampers.

1 2 3 4 5 6 7 8 9 10 11   12

Got loads of brand new parts from Justkampers today. Wow what a quick delivery! Basicly a new bus chassi in parts. Removed front beam, torsionarms and brakes. I think every nut and bolt had to be cut, they were froozen stuck! But it dosen’t matter everything going to be replaced with new parts anyway. Need to remove all chassi parts for sandblasting and painting!


  

Stephan’s Baywindow have come a long way. Painted in primer tonight. The 2.0L engine have been overhauled as well and is soon ready to be installed. Question is; what color is it going to be?

stephan2stephan1stephan

During the summer the Gasoline Magazine came by the garage for a photoshoot and quick interview. Read all about it in the latest issue, in stores now! Or visit: www.gasolinemagazine.se

imageimage image