Have got much done on the VAG 1,9 AEF diesel engine the last days. Dieselpump cleaned up and wiring is fixed. Only 3 sensors are used now. There is alot of wiring and electric sensors that is not needed in a van. (removing immobilizer for example). I moved the dipstick hole to the other side of engine, as it is tilted 45degrees in the bus also are on the wrong side. So drilling a new hole in the engine block was needed. And the old was tapped and sealed up with a 12mm bolt. The tube from the AEF was used and modified/bracket.
The intake manifold don’t fit in the tight bus engine compartment so the old one from the 1,6 CS are going to be used, it has a better angel/shape that fits inside the bus compartment. But it’s a little smaller in diam so I made a port matching (as close as possible) for better flow. The exhaust manifold, I probably going to use the AEF, its bigger in diam than 1,6 so will improve the performance. The downside is I must make a custom exhaust and blank off the EGR valve. Hopefully worth it in the end!
New water pump and thermostat is installed. New timing belt and tensioner etc. Changed flywheel to the 1,6 CS, new needlebearing (don’t forget!) new throw out bearing, new clutch kit. I used new bolts from FEBI to the flywheel, standard size. I took the backing plate from the 1,6 as it will fit the bus transmission better. Also needed to remove two upper studs from engine bolt holes, bolts straight thru will be used instead.
All sensor need to be taken from the old engine (good since I bought all these new awhile ago) like oil pressure, water temp, glow plug sensor etc. Waterflange in alu with sensor was taken from the 1,6 also. All waterlines and hoses to oil cooler etc was removed. Next up is changing oilpan to bus cast alu 1,6 CS. The oilfiller tube has to be removed and plugged, the servopump will be in the way. Will use the cap in the camcover instead. New alternator and servopump, waterpump pulley, idlerwheel and new fan belt is going to be installed next time. Also some new resistors and relays need to be added to the glow plug sensor and relay for coldstart etc.
Transmission have also been removed from the bus now, getting it ready for overhaul and difflock, new seals and shifter bushings. More about that soon…
Another really good page for AEF conversion is Colins write-up on Brick-Yard forum, here is the link: http://www.brick-yard.co.uk/forum/1-6cs-to-aef-engine-swap_topic52595.html
#vwt3overland
The interior is almost finished now, just some small details left to do. Here is how it looks so far… it so nice with heater on the winter, it was -9 celsius and inside was set to 26+celsius 🙂
#vwt3overland
The wiring was a mess (for all equipment) so a new control panel with automatic fuses was installed togheter with new wiring. The 230v wiring (camping power) was also updated with automatic ground fuse and two new sockets with combined USB outlets.
The old interior lightbar was only 230v, but it was a great design so you can flip/turn the light angle. So I took it apart and converted it to 12v with LEDs. An extra LED light with two touch dim/settings was mounted up in the front of the sealing/roof also.
Under the rock n roll sofa I made space for 200amp of batteries (dual 100amp). These I connected to the car/start battery thru a relay, so the car alternator will charge all battery’s. These batteries are connected thru Bluetooth to my cellphone so I can see how much power is left and how much is charging. The solar panel (portable 120w) have a quick connection to these battery’s. Also the 5kw diesel heater is installed under the sofa. It takes air from outside and diesel from the main tank, and the exhaust is routed thru a silencer and out. It runs on diesel and 12v so it can be used anywhere for a very longtime, no need for 230v power. It has a digital display, and a thermostat so it will keep the inside toasty warm on winter. It can be started thru GSM net with my phone. I routed the heater outlets to the main floor and one to the back/bed. It works great and produce a lot of warm dry heat!
The walls, doors and roof was already insulated with 50mm cellplastic, thats very good! But I had some extra aluminium/bubblefoile rolls that I put inside some of the doors and walls for some extra insulation and vapor barier.
#vwt3overland
Have been working on the camping interior lately. The old interior was crappy and looked like shit, it had some structure wall weave/papper that hade been rolled with paint 10 times, the touch and feel was like a 40 grit sandpaper so it needed to go. But it was a good design/plan layout on the cabinets and storage. So I decided to keep the base of it and make a new outside finish on it in light grey oak vinyl.
All cabinet doors was made new in 12mm Medium Density Fibreboard and painted in medium gloss grey with paintgun. Countertop was made new in black colored MDF with semi-gloss clear coat, now with space for a portable kitchen / stove. Above the stove space I made a 12v kitchenfan with outlet, the fan is moving 3,8 squaremeters of air per minute so now you can make bacon with closed doors without smoke/smelling anything 😉
All the old gas equipment was removed, and the old fridge was replaced with a modern 12v Waeco 48L fridge with freezer. A new black sink and a new Reimo water tap was mounted. And all new waterlines, pump and 20L freshwatertank. Before the water ran straight out on the ground, now it goes into a 10L tank first, with a valve so the water can be emptyed. This is good of you are using water when you are on a parkinglot, ferry or on a big camping with neighbors.
Part 2 is coming on Tuesday…
#vwt3overland
Another generation to the collection, at the moment I now have T1, T2 and T3 buses. This one is going to be the offroad bus and for autumn/winter camping/expeditions 🙂
It’s a 1983 Transporter with 1,6 Diesel and 4-speed transmission. It has a ugly camping interior already fitted that will get a refresh/restoration. A Webasto/Planar diesel heater with thermostat will be installed to the interior in future, so you can stay warm on the winter. New 12v fridge will be installed and the gas stove will be replaced with a new small portable gas bottle one.
The goal is to have it pass the MoT / Safety Inspection before the winter comes. The engine starts but is not running very well. It has a new cam, timingbelt, waterpump at the moment. Going to align the timing belt better because it squeaks at lower RPM right now. Also the diesel pump is needing adjustment with special VW TOOL 2066.
Some meaty offroad tires (Malatesta Kobra) have been fitted on stock VW 14″ steel wheels, that was sandblasted and painted. Looks badass now! The diesel tank have been drained on old diesel and a new fuel filter fitted. Also added some anti-bacteria and injectioncleaner to new diesel. New oil (15w-40 mineral) and filter in the engine too. New air cleaner filter added. Injection pump adjusted with micrometer (vw2066) up to 00,95, before was only 00,81. Engine now runs much smoother but need to align the timingbelt before any real test drive can be done. More too come soon… 
